1. Firstly, we shall understand the staff’s position and the layout of division of labor in the service process; the receiver is installed on the reception desk where attendants gather or the stairs entrance or corridors in business hall where it is easier to collect the sights.
2. If the store is of hierarchical management, it is better for every floors to be installed a receiver so as to facilitate the attendant to see the customer call information on their floor.
3.The layout of store directly affect the installation location and number of the receiver:
● Flexural and dispersive arrangement: If the business area is small, then the receiver is installed in the reception desk; such as business area (greater than 100 meters away from the receiver), shall considered the installation of more than one receiver, so that room at different directions is be managed separately and adjust the staff station subsequently to achieve service quickness.
● Linear symmetrical arrangement: the receiver will generally be placed in the reception desk or corridor walls of each floor;
● Both linear and flexural distribution: generally, the room of linear distribution is installed a receiver on the corridor walls separately; while other places with more corners, then consider adjusting the waiter's station, a receiver will be placed in the region of more dense room and after the service personnel as this region see call information, in a timely inform the service personnel at other stations in time for customer service. Service personnel with mobile-type receiver host can also be considered to receive call signal anywhere and provide the timely service.
4. The store's business area impacts directly the installation number of the receivers:
● Layered area is more than 3,000 square meters, the service personnel generally in reception desk on the first floor or near to the reception desk, considering to only installing a receiver in the reception desk.
●Layered area is 3,000 square meters, the service personnel is managed separately, considering installing a receiver for each floor.
● Layered area is more than 5,000 square meters, and the floor’s east and west or north-south distance is over 150 meters, according to a wall blocking nature, consider to install one or more receivers.
● Layered area is over 5,000 square meters, but is a business hall-style without partition, as long as the straight-line distance between the receive and all pages does not exceed 150 meters, then to install a receiver; If you consider the sight distance, two receivers can be installed, so that staff can clearly see display of the call number.
● Layered area is too large, the distance from east to west and north to south is beyond 200 meters; consider installing more than one receiver or installing signal booster.
II. The objective factors to impact receiving distance
1. The customer places where installed a large mechanical and electrical equipment or the power total control device, when installation as far away from the this interference body;
2. The customer places where there is a large pool or seafood workshops, etc., when installation as far as possible away from the humid area;
3. The customer places where equipped with a large-scale heating devices (such as fuel heaters), when installing as far as possible away from such devices;
4. There are more reinforced concrete columns indoor, that will impact the receiving distance to a certain extent;
5. the customer has used other wireless products, such as wireless radio, wireless order (FM section of such products can be adjusted, our product spectrum is 433.92, as long as these products away from our band frequency, the signal will be improved);
6. The hospital is equipped with large ultrasonic equipment; do not install these products nearby.
III. Testing Calling and Receiving Effect
1. The receiver placed in the selected location, opening up the receiver antenna to a 45 degree angle pointing to the direction of pagers. Adjusting the wait time length of digital display according to the customer requirements (see instructions)
2. Three or more different pager numbers were set up (see manual- setting method), making test to the farthest receiving distance;
3. If the receiving effect is poor or unstable, changing receiver position and test again until you find the best receiving position.
4. When two persons making test together, one pressing several pager of different numbers by one-time sequentially, the other one writing down the number display case , to select the pagers that it is the most stable to send and receive signal information for installation in the further room or desk table.
5. Repeating the test as described above for the other receiving direction
IV. Installation Procedures:
1. Plug in the power transformer, firstly, switching on the host power adapter (careful not to use wet hands) until the red light is on and turn on the host, then turn on the switch properly.
2. Check the receiver's starting music is normal.
3. Mounting the receiver in the selected location, the receiver antenna to start a 45 degree angle pointing to the direction of pagers.
4. Digital display needs to be adjusted according to the customer waiting time (refer to instructions).
5. The number of voices needs to be adjusted according to the number of customers (see instructions).
6. Pager numbers will be changed into customer acceptance number based on customer needs. (For adjusted into a special number, refer to instructions). As registration, the both should maintain certain distance, preferably over 30 cm apart; and others not to press pager. If individual registration number not registered on when more numbers are registered at one time is normal, just re-registration again; if the registration number is wrong, should first delete the original error number, and then register a new number.
7. Test before you install the pager, finding the best place before the installation. Directly installing with adhesive tape that a pager brings with, you can also use the nail to fix it in proper place. Note that the indicator of page is aligned in the direction of receivers as far as possible to enhance the receiving effect and sensitivity.
8. And then to install all of the pagers in proper order.
9. And finally re-tested the receiving effect of installed pagers again.
10. Directing customer how to use the instructions.
V. Please note the following as installation
1. Please contact the after- sale department of manufacturer, do not to disassemble the product yourself so as to avoid unnecessary trouble when you found the product is abnormal.
2. The selected configurations of our company’s products are optimum, based on product performance. It is recommended to use original accessories (such as power adapter, batteries). In addition, the key of APE560 pagers should be kept properly that will be used as installing the pager.
3. Please avoid frequently turning on or off power supply, likely causing components damage or product short-circuit in use.
4. The pager can not come directly into contact with the metal base.
5. It is better that pager is attached to the smooth surface as possible, easy fall off from rough surface (such as wallpaper).
6. Please pay attention to moisture protection. Damp place is easy to cause the circuit oxidation.
7. The receiving distance will be different between the rainy and sunny days.
8. If you want to change the pager’s position after installation, firstly using alcohol to infiltrate the tape, then slowly take it down.
9. Check regularly if the product’s electric quantity is adequate in the service so as not to affect the use effect. Pager's battery lifespan is generally 8-12 months, change the batteries in time as director is of micro-lights (director in the dim light within the normal period is not entirely due to the low power, that should be timely to call the manufacturer after-sales department to resolve).